EEE-ULTRA SHINE
Cut 'n' Polish Paste Wax

EEE - Ultra Shine is a cut and polish paste wax containing Tripoli powder (also known in Australia as Rotten Stone) an ultra fine abrasive. The polish is designed to be used in conjunction with Shellawax Cream & liquid or as a finish in its own right on plastics and some stone.

It can also be used by French Polishers after polishing and restorers to cut & polish old polished surfaces.

Many other finishes will also be greatly enhanced by using EEE - Ultra Shine to finish the finish. These include Organ Oil, Danish oil, polyurethane, nitrocellulose lacquer, French polish, spirit varnish, spa vanish, etc.

EEE - Ultra Shine has the unique ability of breaking down the grit size as you use it however instead of becoming blunt like most other abrasives it continues to cut which takes your finish to a higher and higher shine as you continue to work. For woodturners it also has the ability of removing sanding marks from most timbers and can greatly reduce your sanding time whilst giving you a far better finished surface than you have ever had before. A blemish free surface pre-polished and ready to apply your finish to.

If you sand to 240 grit then use EEE it will give you about the equivalent of sanding with 2,000+ grit or more. The higher grit abrasive paper you use before using EEE the better your finish will be. If you sand to 1200 - 1500 grit and then use EEE you will get about the equivalent of sanding up to somewhere between 20,000 & 30,000 grit depending on the material you are working on ant the length of time you are prepared to put into the application (rubbing)..

In pretty well all cases what you will be left with is a surface that shows no sanding marks and is ready to have Shellawax or Shellawax Cream applied to it as a final finish which is guaranteed to knock your eyes out.

If you use either of our Shellawaxes and are amazed at the finish you get with them, prepare yourself to be astounded. This finish is nothing short of miraculous.

If you are striving for perfection in the look of your finish? This is it.

If you are not striving for perfection in the look of your finish. This will give it to you anyway.

If you are sick of spending hours on a finish that is at the best mediocre then try this, combine it with Shellawax on your woodturning and you will never look back.

ON RAW TIMBER:

Sand your turned item to a minimum of 400 grit abrasive (for fine turned items you may wish to sand up too 1200 grit or more). Stop the lathe & apply an even coat of EEE - Ultra Shine with a clean soft rag.

Turn the lathe on and work the wax over the surface with the rag as you would work the surface with an abrasive paper.

Finally, with the lathe still running buff off the remaining wax and abrasive grit with a clean piece of soft cloth then apply Shellawax or Shellawax Cream.

Above: Egg sanded with 180 grit abrasive then with EEE- Utra Shine.     Right: close up of the same egg showing no sanding marks. It is now ready to be polished

ON CRUSHED VELVET DECORA & OTHER PLASTICS:

On pens etc. made with crushed velvet or any of the other plastic type finishes EEE - Ultra Shine - Ultra Shine can be used as the sole finish. Sand with 240 to 400 grit wet and dry abrasive paper using water as a lubricant then apply EEE - Ultra Shine as above working the polish over the surface until the desired effect is obtained. You should have a brilliant blemish free shine on the surface.    

Left & right: These pieces of Decora were given a very quick sand with 180 grit abrasive then finished with EEE - Ultra Shine even when closely inspected with a magnifying glass there are no sanding marks visible.

OVER POLISH:

EEE - Ultra Shine can also be used after the application of Shellawax to finely cut the surface giving a brilliant dry shine. Used over Organ Oil, Danish oil, polyurethane and lacquered surfacer as a final finish EEE - Ultra Shine will give the same brilliant dry shine rather than that wet looking shine that many finishes get.

FOR STONE:

EEE - Ultra Shine is used with brilliant results on Jadewood (Mineral Talc stone). Wether being used in the lathe or polished by hand the result is nothing short of spectacular. If the stone is then finished with Shellawax Cream and then cut again with the EEE the finish is even more brilliant and also well protected.

 (Right: Jadewood polished with EEE)

No other stones have been tested yet but it is possible that this will work well on many others.

FOR FRENCH POLISHERS/RESTORERS

Use EEE - Ultra Shine as a final finish over a polished surface to enhance the finish and remove or at least hide (blend in) slight surface imperfections.

Allow the French polished surface to harden approximately 2 days, then apply the wax to the surface using a clean soft cloth and rubbing with the grain of the timber. Buff off with another clean soft rag turning regularly to remove the grit.

Finally Polish over the entire surface using our Polish Reviver this will remove the last traces of grit and give the surface a brilliant glow.

Combine EEE Ultra Shine with Polish Reviver for brilliant results on old French polished & lacquered surfaces. restores faded, dull, smoke stained, water marked surfaces to like new and much more.

THESE INSTRUCTIONS ARE MEANT AS A GUIDE ONLY. YOU WILL PROBABLY FIND MANY, MANY MORE USES FOR THIS PRODUCT.

We have had reports of it working brilliantly in various metals, bone, shells, Tugua nuts, a variety of polished and painted surfaces and even as a cut and polish on a car (We do not recommend it as a cut and polish for cars but it does work).

Special note for EEE on raw timber

EEE-Ultra Shine is not a finish for raw wood.

When EEE is used on a lathe on raw timber it produces a brilliant shine. Do not be fooled into leaving the wood like this. It is the timber shining from the super fine abrading. There is no finish on the wood. Because of this the timber will dull in a short period of time from moisture in the air, steam, humidity, etc. This is because the timber is still raw. If it gets wet it will dull off instantly.

Please use a finish over the top preferably one of the Shellawaxes, which are 100% compatible with the EEE. You can also use Traditional Wax or our Shithot Waxtik or any other wax over it. However because the wax in EEE is so tenacious it is possible that it may stop any other finish from adhering to the surface. So, if you intend using another finish EEE do a test piece first to make sure it will work. his may avoid some tears down the track.

---

Please take note of the following

---

THIS IS A WAX.
WAX MELTS IN EXTREME HEAT
SO KEEP IT COOL!

To fix melted EEE: Put container in hot water to melt contents, when melted stir with non
metal stirrer until mix begins to cool & thicken or the abrasive may drop out of the mix.

To rejuvenate hard EEE: Do the same as above but, add a small amount of mineral turpentine.
(for half a jar add 1 tablespoon, if really dry add 2 tablespoons too much will just make it runny)

 DO NOT leave rag inside jar.

 Please ensure the lid is always securely fastened.